DTP T HWP 4K 231 D – HDMI Transmitter Decorator-Style Wallplate 230 feet (70 m) – White
DTP T HWP 4K 231 D – HDMI Transmitter Decorator-Style Wallplate 230 feet (70 m) – White - Image 2
DTP T HWP 4K 231 D – HDMI Transmitter Decorator-Style Wallplate 230 feet (70 m) – White - Image 3
,

DTP T HWP 4K 231 D – HDMI Transmitter Decorator-Style Wallplate 230 feet (70 m) – White

Availability:

10 in stock
Compare

46,000 EGP

10 in stock

DTP T HWP 4K 231 D – HDMI Transmitter Decorator-Style Wallplate 230 feet (70 m) – White

Compare
Max. 4k Capabilities
  
   Frame rate1 24, 25, 30, 50, or 60 fps
   Chroma sampling1 4:4:4, 4:2:2, or 4:2:0
   Color bit depth1 8 bits per color
   Signal Type HDMI 1.4, HDCP 2.3
   Max. video data rate 10.2 Gbps (3.4 Gbps per color)
    NOTE 1Subject to the maximum data rate limit. Use our calculator (www.extron.com/8Kdatarate) to determine video parameters supported by this data rate.
Video
   Maximum data rate 10.2 Gbps (3.4 Gbps per color)
   Maximum pixel clock 300 MHz
   Resolution range Up to 2560×1600* @ 60 Hz or 4K (4096×2160) @ 30 Hz, UHD (3840×2160) @ 30 Hz,
4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(*Reduced blanking)
   Color bit depth 8, 10, or 12 bits — subject to the maximum data rate limit
   Formats RGB and YCbCr digital video
   Standards DVI 1.0, HDMI 1.4, HDCP 2.3, CEA-861E
Video input
   Number/signal type 1 single link HDMI (or DVI-D*) input
   Connectors 1 female HDMI type A
    NOTE *Appropriate HDMI to DVI-D cables or adapters are required for HDMI signal input/output.
Interconnection between transmitter and receiver
   Connectors 1 female RJ-45 per unit for 1 cable connecting the transmitter and receiver
   Termination standards TIA/EIA T568B
   DTP signal
      Signal transmission distance
         1080p @ 60 Hz Up to 230′ (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable
         2560×1600 @ 60 Hz Up to 130′ (40 m) using STP cable or XTP DTP 24 cable
         4K/UHD @ 30 and 60 Hz Up to 130′ (40 m) using STP cable or XTP DTP 24 cable
      Cable requirements Solid conductor, 24 AWG or better
      Cable recommendations 400 MHz bandwidth STP cable
    NOTE Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
    NOTE Output mode signaling:

DTP:            HDMI with embedded audio, analog audio, RS-232 and IR, and remote power
HDBaseT:    HDMI with embedded audio plus RS-232 and IR
Audio
   Gain Unbalanced output: 0 dB; balanced output: +6 dB
   Frequency response 20 Hz to 20 kHz, ±0.5 dB
   THD + Noise 0.03% @ 20 Hz to 20 kHz at maximum output
   S/N >90 dB at maximum output (15 dBu), balanced (unweighted)
   Stereo channel separation >80 dB @ 1 kHz to 20 kHz
Audio input
   Number/signal type 1 stereo (2 channel), unbalanced
    NOTE Analog audio is not embedded onto the digital video signal. Analog audio and digital embedded audio are transmitted simultaneously and output on the receiver on two different connectors.
   Connectors (1) 3.5 mm stereo jack, 2 channel; tip (L); ring (R); sleeve (ground)
   Impedance >10k ohms, DC coupled
   Nominal level -10 dBV (316 mVrms)
   Maximum level +7 dBV, unbalanced
    NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Communications — external device (RS-232/IR over TP)
   Serial control port RS-232 via (1) 3.5 mm, 5 pole captive screw connector<BR>(connector is shared with IR control port)
    NOTE Protocol is mirrored between the connected DTP 230 or DTP 330 endpoints and the “Over TP” ports on the
DTP T HWP 231 D. Signals from a control device pass into each “Over TP” port, are embedded with the DTP signal, and sent to the individual DTP 230 Tx or Rx endpoints for control of remote sink or source devices. The “Over TP” ports are simply pass-through connections to DTP endpoints.
   Baud rates Up to 115200 baud
   Protocol Data bits = 5 – 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
   Serial control pin configuration Captive screw connectors: 1 = Tx, 2 = Rx, 3 = Gnd
   IR control port (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
   IR control pin configuration 3 = Gnd, 4 = IR Tx, 5 = IR Rx
General
   Power supply External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts
   Power consumption
      Device 3.0 watts
      Device and power supply 3.9 watts
      Remote power budget 12 watts
    NOTE Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
   Ambient temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
   Cooling Convection, no vents
   Thermal dissipation
      Device 10.0 BTU/hr
      Device and power supply 13.3 BTU/hr
   Mounting
      Furniture or wall mount Yes, with a 1-gang wall box or mud ring
   Enclosure type Metal
   Enclosure dimensions
      Faceplate 2.6″ H x 1.3″ W x 0.3″ D
(6.6 cm H x 3.3 cm W x 0.6 cm D)
      Device 2.8″ H x 1.7″ W x 1.9″ D
(7.1 cm H x 4.3 cm W x 4.8 cm D)
    NOTE Overall height is 4.2″ (10.7 cm), including mounting tabs. Mounting holes are 3.2″ (8.2 cm) apart on center.
Depth excludes connectors. Fits the opening in a 1 gang decorator wallplate).
   Product weight 0.2 lbs (0.1 kg)
   Regulatory compliance AN/NZS, c-UL, C-tick, CE**, FCC Class A**, ICES, UL
    NOTE **CE and FCC testing is conducted with STP cable.
SKU: #0153 Categories: ,

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “DTP T HWP 4K 231 D – HDMI Transmitter Decorator-Style Wallplate 230 feet (70 m) – White”

There are no reviews yet.

Related products

SHOPPING CART

close