,

DTP HDMI 4K 230 Tx – HDMI Transmitter 230 feet (70 m)

Availability:

9 in stock
Compare

36,915 EGP

9 in stock

DTP HDMI 4K 230 Tx – HDMI Transmitter 230 feet (70 m)

Compare
Max. 4k Capabilities
  
   Frame rate1 24, 25, 30, 50, or 60 fps
   Chroma sampling1 4:4:4, 4:2:2, or 4:2:0
   Color bit depth1 8 bits per color
   Signal Type HDMI 1.4, HDCP 2.3
   Max. video data rate 10.2 Gbps (3.4 Gbps per color)
    NOTE 1Subject to the maximum data rate limit. Use our calculator (www.extron.com/8Kdatarate) to determine video parameters supported by this data rate.
 NOTE This product consists of a transmitter (DTP HDMI 4K 230 Tx) and a receiver (DTP HDMI 4K 230 Rx), sold separately, with twisted pair cables linking the transmitter and receiver.
 NOTE *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.
Video
   Maximum data rate 10.2 Gbps (3.4 Gbps per color)
   Maximum pixel clock 300 MHz
   Resolution range Up to 2560×1600* @ 60 Hz or
4K (4096×2160) @ 30 Hz, UHD (3840×2160) @ 30 Hz,
4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(* reduced blanking)
   Color bit depth 8, 10, or 12 bits — subject to the maximum data rate limit
   Formats RGB and YCbCr digital video
   Standards DVI 1.0, HDMI 1.4, HDCP 2.3, CEA-861E
Video input — transmitter
   Number/signal type 1 single link HDMI (or DVI-D*)
   Connectors 1 female HDMI type A
Interconnection between transmitter and receiver
   Connectors 1 female RJ-45 per unit
   Termination standard TIA/EIA T568B
   Signal transmission distance
      1080p @ 60 Hz Up to 230′ (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
      2560×1600 @ 60 Hz Up to 130′ (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
      4K/UHD @ 30Hz and 60 Hz Up to 130′ (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
   Cable requirements Solid conductor, 24 AWG or better
   Cable recommendations 400 MHz bandwidth, STP (shielded twisted pair)
    NOTE Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Video output — receiver
   Number/signal type 1 single link HDMI (or DVI-D*)
   Connectors 1 female HDMI type A
Audio
   Gain Unbalanced output: 0 dB; balanced output +6 dB
   Frequency response 20 Hz to 20 kHz, ±0.5 dB
   THD + Noise 0.03% @ 20 Hz to 20 kHz at maximum output
   S/N >90 dB, at maximum output (15 dBu), balanced (unweighted)
   Stereo channel separation >80 dB @ 1 kHz to 20 kHz
Audio input
   Number/signal type 1 PC level stereo, unbalanced
    NOTE Analog audio is not embedded onto the digital video signal.  Embedded digital audio is not de-embedded from the digital video signal.
   Connectors (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground)
   Impedance >10k ohms, DC coupled
   Nominal level -10 dBV (316 mVrms)
   Maximum level +7 dBV (unbalanced)
    NOTE 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output
   Number/signal type 1 stereo (2 channel), balanced/unbalanced
   Connectors (1) 3.5 mm captive screw connector, 5 pole
   Impedance 50 ohms unbalanced, 100 ohms balanced
   Gain error ±0.1 dB channel to channel
   Maximum level (600 ohm) >+11 dBu, balanced
Control/remote — external device (pass-through, unidirectional or bidirectional)
   Serial control port input/output
      Transmitter RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port)
      Receiver 1 set of proprietary signals on a female RJ-45 jack
   Serial control port output/input
      Transmitter 1 set of proprietary signals on a female RJ-45 jack
      Receiver RS-232 via a 3.5 mm, 3 pole captive screw connector
   Baud rate and protocol 300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity
   Serial control pin configuration 1 = Tx, 2 = Rx, 3 = Gnd
   IR control port (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
   IR control pin configuration 3 = Gnd, 4 = IR Tx, 5 = IR Rx
General
   Power supply External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts
   Power consumption
      Transmitter
         Device 2.5 watts
         Device and power supply 3.4 watts
         Remote power budget 12 watts
      Receiver
         Device 4.2 watts
         Device and power supply 5.8 watts
         Remote power budget 12 watts
    NOTE Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
   Ambient temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
   Cooling Convection, no vents
   Thermal dissipation
      Transmitter
         Device 7.4 BTU/hr
         Device and power supply 10.4 BTU/hr
      Receiver
         Device 13.0 BTU/hr
         Device and power supply 18.7 BTU/hr
   Mounting
      Rack mount Yes, with optional 1U high rack shelf
      Furniture mount Yes, with optional under-desk mounting kit
   Enclosure type Metal
   Enclosure dimensions
      Transmitter 1.0″ H x 4.3″ W x 3.0″ D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors.)
      Receiver 1.0″ H x 4.3″ W x 6.0″ D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.)
   Product weight
      Transmitter 0.5 lbs (0.3 kg)
      Receiver 1.0 lb (0.5 kg)
   Regulatory compliance CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI,
Complies with the appropriate requirements of RoHS, WEEE
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply.
SKU: #0150 Categories: ,

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “DTP HDMI 4K 230 Tx – HDMI Transmitter 230 feet (70 m)”

There are no reviews yet.

Related products

SHOPPING CART

close