,

CRESTRON HD-DA2-4KZ-E AMPLIFIER

Availability:

83 in stock


32,085 EGP

83 in stock

CRESTRON HD-DA2-4KZ-E AMPLIFIER

Compare
Video
Input Signal Type HDMI w/HDR10, Deep Color, 3D, & 4K60 4:4:4 support [1] (DVI & Dual-Mode DisplayPort compatible [2])
Output Signal Type HDMI w/HDR10, Deep Color, 3D, & 4K60 4:4:4 support colspan=”3″1] (DVI compatible[2])
Copy Protection Selectable for HDCP 2.2, HDCP 1.4, or HDCP disabled
Maximum Resolutions

Scan Type Resolution Frame
Rate
Color
Sampling
Color
Depth
Progressive 4096×2160 DCI 4K
or
3840×2160 4K UHD
24 Hz 4:4:4 36 bit
30 Hz 4:4:4 36 bit
60 Hz 4:2:2 36 bit
60 Hz 4:4:4 24 bit
2560×1600 WQXGA 60 Hz 4:4:4 36 bit
1920×1080 HD 1080p 60 Hz 4:4:4 36 bit
Interlaced 1920×1080 HD 1080i 30 Hz 4:4:4 36 bit

NOTE: Common resolutions are shown; other resolutions are supported at pixel clock rates up to 600 MHz

Audio
Input Signal Type HDMI (Dual-Mode DisplayPort compatible[2])
Output Signal Type HDMI
Formats Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS®, DTS-ES, DTS 96/24, DTS HD High Res, DTS HD Master Audio, DTS:X, LPCM up to 8 channels
Communications
USB USB 2.0 host; supports firmware update and custom EDID upload via a USB flash drive
HDMI HDCP & EDID (does not pass CEC)
HDCP Version Selectable for HDCP 2.2, 1.4, or OFF;
HDCP encrypted content is blanked in OFF mode
EDID Mode Selectable for DEFAULT or COPY 1ST;
• The factory default EDID is 4K60 4:4:4 non-HDR video with 2-channel LPCM audio;
• The factory default EDID can be replaced with a custom EDID via USB;
• Sliding the switch from DEFAULT to COPY 1ST copies and stores the EDID from the device at OUTPUT 1 and passes it to the INPUT source device;
• Sliding the switch from COPY 1ST to DEFAULT erases the stored EDID and uses the factory default or custom EDID;
Note: Changing the device at OUTPUT 1 will not update the stored EDID until the switch is moved to DEFAULT and back to COPY 1ST
Connectors
INPUT (1) HDMI Type A connector, female;
HDMI digital video/audio input[1];
(DVI & Dual-Mode DisplayPort compatible[2])
OUTPUT 1 – 2 (2) HDMI Type A connectors, female;
HDMI digital video/audio outputs[1];
(DVI compatible[2])
SERVICE (1) USB Type A connector, female;
USB 2.0 host port;
For firmware update and custom EDID upload via a USB flash drive
24VDC 0.75A (1) 2.1 x 5.5 mm DC power connector;
24 Volt DC power input;
PW-2407WU power pack included
Controls & Indicators
PWR (1) Bi-color LED, indicates operating power is supplied via the power pack; illuminates amber while booting, green when operating
SETUP (1) Pushbutton and (1) red LED, restores factory settings
RESET (1) Recessed pushbutton for hardware reset
INPUT (1) Green LED, indicates video signal presence at the HDMI input
OUTPUT 1 – 2 (2) Green LEDs, each indicates video signal transmission at the corresponding HDMI output
HDCP (1) 3-position slide switch, selects the HDCP version (OFF, 1.4, or 2.2)
EDID (1) 2-position slide switch, selects the EDID mode (DEFAUT or COPY 1ST)
Power
Power Pack (included) Input: 100-240 Volts AC, 50/60 Hz;
Output: 0.75 Amps @ 24 Volts DC;
Model: PW-2407WU
Power Consumption 4.3 W (typical)
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% RH (non-condensing)
Enclosure
Chassis Metal, black finish, with (2) integral mounting flanges
Mounting Freestanding, surface mount, or attach to a single rack rail
Dimensions
Height 0.87 in (22 mm)
Width 5.73 in (146 mm)
Depth 4.67 in (119 mm)
Compliance
CE, IC, FCC part 15 Class B digital device
SKU: #0091 Categories: , Tag:

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “CRESTRON HD-DA2-4KZ-E AMPLIFIER”

There are no reviews yet.

SHOPPING CART

close