Transducer type . . . . . . . . . . . . . . . . Condenser (back electret)
Operating principle . . . . . . . . . . . . . Pressure gradient
Polar pattern . . . . . . . . . . . . . . . . . . Supercardioid
Frequency response:
Close miking . . . . . . . . . . . . . . . . . 20 – 13,000 Hz
Distant miking (measured at 1 m) . . . 180 – 13,000 Hz
Open circuit voltage . . . . . . . . . . . . . 6.0 mV/Pa (-44.5 dBV)* ±3 dB
Nominal impedance . . . . . . . . . . . . . approx. 700 Ω
Load impedance. . . . . . . . . . . . . . . . > 3.5 kΩ
Max. SPL at 1 kHz . . . . . . . . . . . . . . 119 dB*
Equivalent SPL . . . . . . . . . . . . . . . . . 31.5 dB SPL*
Power supply . . . . . . . . . . . . . . . . . . Direct current 1.5 – 9 V
Max. power consumption . . . . . . . . 780 µA
Connector . . . . . . . . . . . . . . . . . . . . Mini-XLR, 4-pin, female
Dimensions:
Diameter. . . . . . . . . . . . . . . . . . . . 15 mm
Length microphone boom. . . . . . . 95 mm
Weight. . . . . . . . . . . . . . . . . . . . . . . 36 g
Beyerdynamic – TG 534 518-548 MHz
10 in stock
29,285 EGP
10 in stock
There are five sets of the Beyerdynamic Manual TG 500 system available; each set comes with a separate receiver and two detachable antennas.
While the TG 556 Vocal Set includes a TG 500H-C handheld transmitter with a TG V56 capsule (condenser capsule, cardioid), which makes it ideal for presentations, the TG 550 Vocal Set comes with a Beyerdynamic Manual TG 500H-D handheld transmitter with a TG V50 capsule (dynamic capsule, cardioid).
For both portable transmitters, matching microphone clamps are available. The TG 534 Headworn Set, which includes a TG H34 neck worn microphone (condenser, super cardioid), is the ideal option for theatrical performances, while the TG L58 clip-on microphone (omnidirectional, condenser) from the TG 558 Presenter Set may be worn discreetly during lectures.
The TG 510 Instrument Set includes the WA-CGI instrument cable (6.35 mm mono jack), which is used to mic electric and bass guitars. See more about beyerdynamic – tg 534 518-548 mhz manual.
Buy Beyerdynamic Manual from OmniSignals now!
Beyerdynamic Manual Parts
TG 500 SR
- Intuitive, user-friendly menu navigation
- Up to 40 MHz switching bandwidth
- Infrared interface for transmitting the settings from the
- Receiver to transmitter
- Backlit LC-Display
- Status display (battery, transmission frequency, name)
- scan function
- Pilot tone function
TG 500 B
- 120 m Range
- Various microphones available for speech, vocals and instruments
- 10 h battery life
- Battery charging via WA-CD charger possible
TG H 34
- Especially suitable for musicians and dancers on stages or in sports lessons
- Easy handling, high feedback safety and an optimal fit
- It is also suitable for presentations of all kinds
Check out the Beyerdynamic – TG 534 518-548 MHz Price!
Technical Data
TG 500 SR
- Frequency ranges: 518 – 548 MHz / 606 – 636 MHz / 794 – 832 MHz / 1780 – 1810 MHz
- Range: up to 120 m (line of sight)
- Number of active channels: 18 per frequency band
- Audio frequency response: 45 Hz – 15 kHz
- Audio dynamic range: 160 dB ( A-weighted )
- Operating principle: Analogue wireless microphone system with diversity receiver
- Output level: max. +3 dBV / +5 dBU
- Display: LCD, white, backlit
- Antenna connection: 2x BNC input
- Power supply: 100 – 240 VAC with plug-in power supply unit
- Power consumption: 3 W (typ.)
- Ambient temperature: 0 to + 55 °C
- Dimensions (WxDxH): 200 x 175 x 42 mm
- Weight: 960 g
TG 500 B
- Display: LCD
- Power supply: 2x AA NiMH or alkaline batteries
- Connection: 4pin Mini XLR
- Operating time: approx. 10h
- Transmission power: 10 mW/ 50 mW
- Frequency range: 606 – 636 MHz
- Ambient temperature: 0 to +55 °C
- Dimensions (WxDxH): 90 x 59 x 26 mm
- Weight: 85 g
TG H 34
- Converter principle: Capacitor (back electret)
- Working principle: pressure gradient receiver
- Frequency range: 20 Hz – 13 kHz (near field) / 180 Hz – 13 kHz (far field, distance 1m)
- Free field transmission factor: 6.0 mV/Pa (-44.5 dBV)* ±3 dB
- Nominal impedance: approx. 700 Ω
- Nominal termination impedance: > 3.5 kΩ
- Max. SPL (at 1 kHz): 119 dB
- Equivalent sound pressure level: 31.5 dB SPL
- Type of power supply: direct current 1.5 – 9 V
- Max. power consumption: 780 µA
- Connection: Mini XLR 4 pin female
- Dimensions (ØxL): 15 x 95 mm
- Weight: 36 g
Based on 0 reviews
Be the first to review “Beyerdynamic – TG 534 518-548 MHz”
Related products
-
Pro Audio, Loudspeakers
LC1-UM12E8 – Ceiling loudspeaker, 12W, coaxial
LC1-UM12E8 ceiling loudspeaker, 12 W, integrated circular metal grille, 6-inch coax (two-way system) driver, without flush ceiling-mounting accessory, EN54-24 certified, white RAL 9010.
Key Features
- superb audio quality for both talking and music
- One grille size and one whole set of accessories make installation simple
- options for various ceiling mounting techniques
- Pilot Tone indicator that is optional
- UL2043, UL1480, and EN 54-24 certified
System Overview
Numerous ceiling situations are suitable for the LC1 Modular Ceiling Loudspeaker series. They offer top-notch music and voice for indoor public address applications. There are five loudspeakers in the range, each with a unique opening angle, input power, and sound reproduction.
The LC1-MFD or LC1-MFDS enclosure may be used to mount the loudspeaker, which are appropriate for usage in areas where air is handled. The DC-blocking board PM1-LISD and optional monitoring board PRA-EOL can be mounted within the enclosure of the loudspeaker frame.
Check out the LC1 ceiling loudspeaker price.
Functions
Voice alarm applications
Voice alarm loudspeakers are made expressly to be used in buildings where rules control the verbal evacuation notification system’s functioning. The LC1 Modular Ceiling Loudspeaker series complies with British standard BS 5839–8 and is approved EN 54–24 for use in voice alarm systems.
Buy LC1 Ceiling loudspeaker, 12W from OmniSignals now!
Protection
In order to prevent connected circuit failure due to fire damage to the loudspeaker, the loudspeaker is equipped with built-in protection. System integrity is preserved in this way, guaranteeing that people can still hear announcements via loudspeaker in other locations.
To further strengthen the safety of the cable termination, the LC1-UM12E8 ceiling loudspeaker can also be utilized in conjunction with a metal fire-dome.
Connections
The LC1-UM12E8 ceiling loudspeaker has a ceramic screw-terminal connection block, thermal fuse and heat-resistant, high-temperature wiring.
Installation/configuration notes
The LC1 ceiling loudspeaker coaxial range is designed with ease of installation in mind, ensuring a user-friendly experience for seamless integration into diverse environments. The loudspeaker consists of a frame with the loudspeaker driver and metal or ABS grille with integrated light conductor, matching transformer and ceramic screw terminal connection block.
On the loudspeaker are provisions for mounting the optional end-of-line surveillance board and optional DC-blocking board. Power tapping on the 70 V / 100 V matching transformer allows selection of full-power, half power, quarter-power and eight-power radiation.
SKU: #0012 -
Pro Audio, Loudspeakers
LC2-PC30G6-8 – Ceiling loudspeaker, 30W, 8″ Pair
The LC2-PC30G6-8 Ceiling loudspeaker is a 8‑inch two‑way Premium‑sound Ceiling Loudspeaker which provides; wide dispersion, high efficiency, high maximum output, ease‑of‑installation, and wide‑range reproduction of music and voice.
Key Features
- 8‑inch coaxial two‑way
- Waveguide coupled Ti tweeter
- Full bandwidth overload protection
- Front baffle wattage tap adjustment
- BS 5839‑8 and EN 60849 compliant
It consists of a baffle assembly, grille, back‑can enclosure, 8‑inch coax two‑way loudspeaker and internal output‑power matching transformer. The loudspeaker features a waveguide coupled with a titanium coated dome tweeter.
The rear enclosure provides an optimum internal volume for extended low frequency performance. The loudspeaker utilizes a second order crossover network at 3.3 kHz, with a comprehensive protection circuit to protect the network, woofer, and tweeter drivers from excessive power levels.
The LC2-PC30G6-8 Ceiling loudspeaker can be installed optionally with the LC2‑PC60G6‑10 ceiling subwoofer to enhance the low frequency reproduction down to 45 Hz.
Mounting
The LC2-PC30G6-8 Ceiling loudspeaker is secured in ceilings using four integral toggle anchors, and has been designed to work together in a wide range of different ceiling constructions.
A tile bridge / C‑ring is included for safe suspension in a drop ceiling that uses mineral wool, or other fiber‑based ceiling tiles from 4 to 25 mm (0.16 to 1.0 in.) thick. A circular template for marking a 272 mm (10.75 in.) diameter hole is included with the loudspeaker.
Check out LC2 Ceiling loudspeaker Price.
Power setting
The LC2 Ceiling loudspeaker Pair has a three‑way emergency compliant ceramic terminal block with screw connections (including earth) suitable for loop‑through wiring.
Four 100 V, and five 70 V, primary taps are provided on the matching transformer to allow selection of nominal full‑power, half‑power, quarter‑power, eighth‑power radiation (in 3 dB steps) and eight ohm. Selection is done via a convenient switch on the front baffle.
Buy LC2 Ceiling loudspeaker, 30W from OmniSignals now!
SKU: #0015 -
Pro Audio, Power Amplifiers
Bosch PLE-1MA120-EU – Priority mixer amplifier, 120W
Bosch PLE-1MA120 Plena Mixer Amplifier: The Ultimate Sound Solution for Commercial Spaces
Elevate your audio experience with the Bosch PLE-1MA120 Plena Mixer Amplifier, designed to cater to the sophisticated needs of background audio PA systems and commercial audio installations. Boasting a robust 120 watts of power, this amplifier is your go-to solution for delivering clear, impactful sound across retail stores, commercial offices, halls, and more.
Key Features at a Glance:
- Powerful Audio Delivery: With 120 watts of output, the PLE-1MA120 ensures your message is heard loud and clear, whether it’s music, announcements, or both.
- Versatile Connectivity: Featuring four microphone/line inputs alongside 3 music source inputs and a dedicated 100V & telephone input, this amplifier provides the flexibility needed for various audio setups.
- Priority & VOX Override: Essential for paging and announcements, the VOX (voice-activated) override function ensures your messages take precedence, seamlessly integrating with the priority input for emergency broadcasting.
- Intuitive Operation: Designed with ease of use in mind, the PLE-1MA120 boasts a straightforward interface, allowing effortless operation by anyone.
- Tailored Sound Control: With adjustable talk-over functions and unique, intuitive tone controls, including a 2-band EQ (Bass: ±12 dB, Treble: ±12 dB), you can fine-tune your audio to perfection.
- Comprehensive Outputs: The amplifier offers output for line out and music only out, with an announcement-only work and a 3-wire volume override, ensuring versatile integration into your existing sound system.
- Reliable Performance: Crafted for consistency, the PLE-1MA120 delivers a frequency response of 50 Hz to 20 kHz +1/-3 dB (at Rated Power -10 dB) with less than 1% distortion at rated power, ensuring high-quality sound reproduction.
Designed for Durability and Convenience:
The Bosch PLE-1MA120 is housed in a tabletop form factor, making it an ideal fit for any setting. It’s engineered for efficiency with a power consumption of 400 VA and a maximum current consumption of 10 A. The package includes everything you need to start, weighing in at 24.55 lb with dimensions of 22.5 x 14.1 x 8.8 inches, ensuring a seamless setup process.
Why the Bosch PLE-1MA120 Plena Mixer Amplifier?
The Bosch PLE-1MA120 Plena Mixer Amplifier is more than just an amplifier; it’s a cost-effective, reliable solution that brings unparalleled clarity and control to your audio installations. Whether for announcements, background music, or emergency paging, the PLE-1MA120 enhances the auditory experience in retail, commercial, and public spaces. Elevate your audio setup with the PLE-1MA120 and ensure your message is always delivered precisely and clearly.
SKU: #0032 -
Pro Audio, Loudspeakers
LC1-UM06E8 – Ceiling loudspeaker, 6W, metal
The LC1-UM06E8 Ceiling loudspeaker range can be used for a wide variety of ceiling environments. They provide excellent speech and music in indoor public address applications. The range offers a choice of five loudspeakers distinguished by input power, opening angle and sound reproduction.
Key Features
- Excellent speech and music reproduction
- Easy installation with one grille size and one complete set of accessories
- Choice of different ceiling mounting methods
- Optional Pilot Tone indication
- EN 54‑24, UL2043, UL1480 certified
Protection
The LC1-UM06E8 Ceiling loudspeaker has built-in protection to ensure that fire damage to the loudspeakers does not cause failure of the connected circuit. In this way system integrity is maintained, ensuring loudspeakers in other areas can still be used to inform people of the situation. The loudspeakers can also be used in combination with a metal fire-dome to increase protection of the cable termination.
Check out the LC1 ceiling loudspeaker price.
Connections
The loudspeaker has a ceramic screw-terminal connection block, thermal fuse and heat-resistant, high-temperature wiring.
Buy LC1 ceiling loudspeaker, 6W now!
More Information
Ceiling loudspeaker, 6 W, integrated circular metal grille, 6-inch driver, without flush ceiling-mounting accessory, EN54-24 certified, white RAL 9010.
The loudspeaker can be installed with the LC1-MFD or LC1-MFDS enclosure and are suitable for use in air-handling spaces. The loudspeaker frame includes provision for mounting the optional monitoring board PRA-EOL and DC-blocking board PM1-LISD inside the enclosure.
See our LC1 ceiling loudspeaker metal.
SKU: #0019
There are no reviews yet.